The Utility New motor First bottom panel cut

This first half of April has seen some progress on the Utility project, although not much that is visible on the actual boat itself. I ordered a new Nissan 8hp motor from onlineoutboards.com. The motor arrived very promptly... and I promptly realized I’d never operated a tiller-controlled boat before.

New 8hp Nissan Marine outboard

So, the kids and I fixed that by taking a weekend getaway at a nearby lake. I rented a 14 ft Jon boat fitted with a 9.9 hp Yamaha, and we ventured out on the water. There really is a lot to be said for the simple Jon boat. They may not be the prettiest things on the water, but it’s hard to imagine a more versatile boat in that size.

In any case, our little aluminum Jon boat was by no means a rocket on the water, but it did what it was supposed to. The Utility will have a shorter, and more streamlined hull, although somewhat heavier. I imagine performance with its 8hp motor will be similar to the 14’ Jon boat with the 9.9 Yamaha. Time will tell.

Over Easter weekend, I began the break-in period for the Nissan motor. The first two phases were to let it run at idle for 10 minutes, then to run at <50% throttle for two hours. That’s done. The next phase is to let it run at <75% throttle.

On the boat framework, I have faired down the side planking on the starboard side. I have not yet tried to fill in any of the low spots, or “hollows”, along the chine. Instead, I decided to go ahead and cut the panels for the bottom planking by cutting one sheet of Meranti in half lengthwise.

My plan is to begin dry-fitting the bottom panel into place, and to use that as a gauge to determine just how much I’ll need to fill in along the chine. It is possible that any gaps will be minor enough that thickened epoxy will do the job adequately.

Rough placement of the first bottom panel

Read More..

The Utility First planking panel attached

Over the weekend, I was finally able to attach the aft starboard side panel with epoxy and screws.

First, before I removed the panel from the boat’s framework, I traced the lines of the chines, sheers, and frame to the inner surface of the plywood. That way, I would have an easy visual reference for where to spread the epoxy. I also drew reference points on both the plywood and the chine to help align the panel when it was time to put it back on.

I removed the panel & set it aside, and staged all the items I’d need nearby: chip brush, extra latex gloves, awl, clamps, screwdriver, and the silicon bronze screws. I kept extra screws close at hand just in case I stripped any screw heads. This time, I put some old newspaper down on the floor to catch any drips of epoxy... right next to the earlier dried globs that I’m going to have to sand off of the concrete at some point.

Planking panel removed & waiting for epoxy.

Frame outlines made a great reference for spreading the epoxy.

Waiting for epoxy.

Some of my alignment was a bit off when I drilled into the sheer. Ill have to be more careful next time.

Same drilling alignment issue with the transom frame.

With everything ready to go, I mixed 6 oz of Silvertip Gel Magic epoxy. Gel Magic is a highly-viscous 2:1 mixture (2 parts resin to 1 part hardener). Its thickness makes it ideal for applying to vertical surfaces and for filling gaps. In this way it is very similar to Glen-L Poxy Grip.

The GelMagic components are color-coded.

Using the chip brush, I applied epoxy to both the plywood panel and the mating surfaces on the boat’s framework. At one point, I was concerned that 6 oz of epoxy would not be enough to do the job. Luckily, however, it was just about right, with a minimal amount of waste.

Wearing 2 layers of disposable latex gloves, I roughly aligned the panel with the reference marks I’d made earlier, and held it in place with one clamp. The Irwin spring clamps are great for this, as the springs in them are quite strong. Next, I used the awl to align the first holes, adjusting the clamp as necessary. I hand-threaded the first screw, then changed gloves to avoid getting too much epoxy onto my screwdriver.

After driving the first couple of screws, I clamped the rest of the panel into position. Hand-driving the screws went very smoothly. I found that using a ratcheting screwdriver with an oversized handle is just ideal for this task. I also found that I’d over-beveled some of the holes, as a few of the screw heads went slightly below the surface of the plywood. I’ll create less of a bevel next time.

With the panel fully “glued and screwed” into place, I used the putty knife to scrape away excess epoxy from the areas where I’ll need to join more wood: the chine and sheer where the forward planking panel will butt up against the aft panel; and the interior joints of the chine and sheer to the aft panel where the backing piece for the butt joint will be attached. I then used the putty knife to fill the screw holes with epoxy.

It was while using the putty knife that I realized the major component of this process that I’d forgotten: 

A rag. 

Thankfully, the laundry basket was nearby. 

There’s one less item I’ll have to wash, dry and fold. Hopefully, however, I will remember to get shop rags next time.

Alignment marks & filled screw holes along the chine.

Excess epoxy was scraped away from the chine so it wont interfere with fitting of the forward panel.

The small gap on the side of the transom is now filled.

Seam of cured epoxy against frame #1.

On the interior seams, I scraped away excess epoxy so it wont interfere with fitting of the backing block for the butt joint.

Read More..

The Utility Fitting the first planking panels

After a brief debate about whether to plank the transom first, or last, I eventually came to the conclusion that it’s a matter of individual preference. Other boatbuilders I trust kindly offered me their opinions, reasons, and techniques. I weighed all of their input before deciding on my own course of action.

I’m going to plank the sides first, and the transom second. That way, the aesthetics of the bright-finished transom should be consistent all the way out to the sides, with no end grain from the side planking visible.

Then I’m going to plank the bottom last. The reason for this basically boils down to ease of construction, regarding the transom. It seems to me that it will be easier to plank the transom while I can still access both inner and outer surfaces of it for clamping. I wouldn’t be able to do this after the bottom is planked. Since the lower edge of the transom will be underwater, then it won’t matter if the end grain is visible (whether or not it’s an aesthetic matter).

Planking
I started by cutting two 2’ x 4’ panels from a sheet of the Meranti. These will be the aft side panels. I clamped the first one into place on the starboard side. Then I roughly traced the trim line with a pencil, and removed the panel. I drew a second line 1” outside the trim line, so the panel would still be slightly oversized after I cut it. I cut it, and checked it against the port side. Since it looked good against the port side also, I used the cut piece as a template to trace out the second panel.

With both panels cut, I clamped them back into position. I’m very happy with the fitting on the starboard side. The port side still needs a little fairing, but it’s close.

Initial fitting of the aft starboard panel.

Aft starboard panel-to-transom fit. This gap will need to be filled in.

Aft starboard panel to frame #1 fit.

Aft starboard panel-to-transom inner fit.

Aft port panel-to-transom fit.

Aft port panel-to-sheer fit. This area needs a little more fairing.

Aft port panel-to-sheer fit, forward of frame #1. This area needs a little more fairing.

Read More..

Incremental progress on the first bottom plank

So, cautiously and methodically, I have continued fastening down the first panel for the bottom planking.

Using a 4-foot ruler as a straight edge, I drew reference lines on the plywood to show placement of the floor battens. That made it much easier to mark the places to drill holes & drive screws. Marking the chines for screw placement has not been so easy. I’ve had to cut away enough overhanging material so that I can use my marking gauge — the same spring clip & duct tape arrangement I used on the side planking. I used the Porter Cable multi-tool saw to cut away plywood as I worked my way forward... cutting new plywood washers as I went.

Bottom panel, before much extraneous material was removed.

Looking forward, you can see the panel begin to curve and twist.

Reference lines for the battens helped greatly with screw placement.

Near the forward frame, the plywood begins to curve and twist considerably. At times, it seemed like I just couldn’t bend it any more without breaking it. I followed the technique outlined in Boatbuilding With Plywood, and cut away as much extraneous material as I could, while still leaving myself adequate material to work with. It is amazing how much easier plywood will bend when excess material is cut away.

Here, a good bit of material has been removed from the panel. It became much easier to bend.

For now, my progress has stopped at the forward frame. I’m just inches away from the transition joint. To mark the approximate cut line up forward, I coated the corner of the side planking with a lumber crayon & bumped the bottom planking panel against it to transfer the mark. It worked reasonably well. Soon, I’ll remove the bottom panel, cut near this line, and re-attach the panel for further fitting.

The transferred line on the inside of the panel should help greatly when I remove the panel & trim it down further.

 Once this panel is cut to shape, I’ll be able to use it as a template for the other panel.

Read More..

First coat of primer

Today I did a bit more sanding on the Utilitys hull... then I taped it off and rolled on the first coat of primer. The primer is AquaGard 190. I rolled it on with a foam roller, and it took only a fraction of a quart to cover the bottom. It was a breeze.

The lighter area you see going across the hull is from water that condensed on an overhead air conditioning duct and then fell onto the hull, before rolling off either side. A little frustrating, but it doesnt look like it will cause a problem. Ill remember to towel off the ductwork before applying the second coat. Maybe that will buy me enough time before the next coat dries.

What can I say? I live in the deep South. It gets humid here.

Read More..